Assembly Instructions for INTEAUTO Push Pull Connectors

Assembly Instructions for K Series Straight Plug

The K Series Straight Plugs can be easily and quickly assembled if you follow the steps given below:

  1. First of all, arrange a bend relief ❶, collet nut ❷, collet ❸, gasket ❹ and earthing cone ❺ in line and pass the cable from them.
  2. You should now solder the small conducting wires from the cable with the insulator insert ❼ contacts.
  3. Cover the insulator insert ❼ using a split insert carrier ❻ by ensuring that the slots of both the insulator insert ❼ and split insert carrier ❻ mounts on each other
  4. Push the earthing cone ❺, gasket ❹ and collet ❸ to the correct position, assembled split insert carrier ❻ and insulation insert ❼ and ensure that the sheath of the cable is properly inserted into the earthing cone ❺.
  5. Now, you must slide the ready insulator insert ❼ into the plug’s outer shell ❽.
  6. At this stage, you must ensure that the slots of both the insulator insert ❼ and the plug’s outer shell ❽ mount with each other.
  7. After insertion, you can now tightly screw the collet nut ❷ onto the plug’s outer shell ❽.
  8. The bend relief ❶ is then connected with the collet nut ❷ to avoid cable bending at the plug’s starting point.

Assembly-Instructions-for-K-Series-Straight-Plug

Figure 1 Assembly Instructions for K Series Straight Plug

Assembly Instructions for F Series Straight Plug

The F Series Straight Plugs can be assembled by the steps given below:

  1. The first step is to arrange the bend relief ❶, collet nut ❷, collet ❸, gasket ❹, and earthing cone ❺ in line with each other and pass the cable inside them.
  2. It is now time to solder the insulator insert ❼ contacts to the small conducting wires inside the cable.
  3. Ensure that both the insulator insert ❼ and split insert carrier ❻ slots mount on each other when covering the insulator insert ❼ with a split insert carrier ❻
  4. Ensure that the cable sheath is properly inserted into the earthing cone ❺.
  5. It can be done by pushing the earthing cone ❺, gasket ❹, and collet ❸ to the correct position of assembled insulation insert ❼ and split insert carrier ❻.
  6. The insulator insert ❼ needs to be inserted into the outer shell ❽ of the plug now.
  7. It is important to ensure that the slots on both the insulator insert ❼ and the outer shell ❽ of the plug align.
  8. The plug’s outer shell ❽ can now be tightly secured with the collet nut ❷ after insertion.
  9. To prevent cable bending at the plug’s starting point, the bend relief ❶ is connected to the collet nut ❷.

Assembly-Instructions-for-F-Series-Straight-Plug

Figure 2 Assembly Instructions for F Series Straight Plug

Assembly Instructions for T Series Straight Plug

In order to assemble the T Series Straight Plugs, follow these steps:

  1. It is a good idea to align the bend relief ❶, collet nut ❷, collet ❸, gasket ❹, and earthing cone ❺ before proceeding.
  2. Pass the cable through a bend relief ❶, a collet nut ❷, a collet ❸, a gasket ❹, and then through an earthing cone ❺.
  3. In order to conduct the small current, the insulator insert ❼ contacts must be soldered to the small conducting wires.
  4. It is important to ensure that both insulator insert ❼ and split insert carrier ❻ slots are in alignment when attaching the split insert carrier ❻ to the insulator insert ❼
  5. Now push the earthing cone ❺, gasket ❹, and collet ❸ into the correct position of the assembled insulation insert ❼ and split insert carrier ❻
  6. At this stage, you must ensure that the cable sheath is inserted properly into the earthing cone ❺.
  7. This is the time to insert the insulator insert ❼ into the plug’s outer shell ❽.
  8. To ensure the plug’s alignment, both the insulator insert ❼ and outer shell ❽ must have aligned slots.
  9. Following insertion, the outer shell ❽ of the plug can be tightly secured with the collet nut ❷.
  10. By connecting the bend relief ❶ to the collet nut ❷, the cable will not bend at its starting point.

Assembly-Instructions-for-M-Series-Straight-Plug

Figure 3 Assembly Instructions for M Series Straight Plug

Assembly Instructions for S Series Straight Plug

These steps will guide you through the assembly of S Series Straight Plugs:

  1. The good idea is to align the bend relief ❶, collet nut ❷, collet ❸, and split insert carrier ❹ before moving on.
  2. Pass the cable through the bend relief ❶, the collet nut ❷, and then the split insert carrier ❹.
  3. Soldering the insulator insert ❺ contacts to the small conducting wires inside the cable is required to conduct the small current.
  4. Once the split insert carrier ❹ is mounted on the insulation insert ❺, make sure the slot of the split insert carrier ❹ fits into the insulation insert’s ❺.
  5. Now is the time to position the cable with the collet ❸ in the right place.
  6. The collet ❸, split insert carrier ❹, and insulator insert ❺ must now be inserted into the outer shell ❻ of the plug.
  7. A collet nut ❷ can be used to secure the plug’s outer shell ❻ after it has been inserted.
  8. In order to avoid cable bends at the plug’s starting point, the bend relief ❶ is now then connected to the collet nut ❷.

Assembly-Instructions-for-S-Series-Straight-Plug

Figure 4 Assembly Instructions for S Series Straight Plug

Assembly Instructions for Coaxial Straight Plug

You can assemble the Coaxial Straight Plugs easily and quickly by following these steps:

  1. To begin with, line up the bend relief ❶, collet nut ❷, and collet ❸.
  2. You should now pass the cable through a bend relief ❶, the collet nut ❷, and finally the collet ❸.
  3. The contact insert ❹ should now be soldered to the conducting material.
  4. In this step, insert the soldered contact insert ❹ into the insulator insert ❺.
  5. On the back of the contact insert ❹, connect the collet ❸ to the correct position.
  6. It is now necessary to insert the insulator insert ❺ into the outer shell ❻ of the plug.
  7. In this step, you must ensure that both the insulator insert ❺ and the plug’s outer shell ❻ have identical slots.
  8. The collet nut ❷ can now be firmly screwed on the outer shell ❻ of the plug after insertion.
  9. The bend relief ❶ is now then connected to the collet nut ❷ to keep the cable straight.

Assembly-Instructions-for-Coaxial-Straight-Plug

Figure 5 Assembly Instructions for Coaxial Straight Plug

Assembly Instructions for M Series Straight Plug

These steps will help you assemble the M Series Straight Plugs quickly and easily:

  1. Place the collet nut ❶, gasket ❷, insulation seal ❸, silicone sealing ring ❹ and outer shell ❺ and insulator insert ❻ in sequential order.
  2. The small conducting wires inside the cable are now passed through collet nut ❶, gasket ❷, insulation seal ❸, silicone sealing ring ❹, and outer shell ❺.
  3. After passing, you should solder the exposed small wires with the contacts of the insulation insert ❻.
  4. After soldering, you can now tightly screw the insulation insert ❻ with the plug’s outer shell ❺.
  5. Now you need to push or insert the silicone sealing ring ❹, insulation seal ❸ and gasket ❷ in order inside the plug’s outer shell ❺.
  6. The final step is to tighten the collet nut ❶ with the plug’s outer shell ❺ by rotating it in the anti-clockwise direction.

Assembly-Instructions-for-T-Series-Straight-Plug

Figure 6 Assembly Instructions for M Series Straight Plug

Assembly Instructions for P Series Straight Plug

If you follow the steps below, you can easily and quickly assemble the P Series Straight Plugs:

  1. The initial step is to line up the collet nut ❶, collet ❷, insulation insert ❸, and outer shell ❹.
  2. Pass the cable through a collet nut ❶, collet ❷, insulation insert ❸, and then the outer shell ❹ in the same order as described.
  3. The insulator insert ❸ contacts and small conducting wires should now be soldered together.
  4. Use a collet ❷ to cover the insulator insert ❸, ensuring that the collet ❷ and the slot on the insulator insert ❸ are aligned.
  5. Into the outer shell ❹ of the plug, push the assembled insulation insert ❸.
  6. It is important at this stage that the collet ❷ lug and the slot of the insulator insert ❸ fit together properly.
  7. The collet nut ❶ can now be tightly screwed onto the outer shell ❹ of the plug after insertion.

Assembly-Instructions-for-P-Series-Straight-Plug

Figure 7 Assembly Instructions for P Series Straight Plug

Assembly Instructions for W Series Straight Plug

If you follow the instructions below, you will be able to assemble the W Series Straight Plugs quickly and easily:

  1. In order to start, arrange a bend relief ❶, collet nut ❷, collet ❸, earthing cone ❹, split insert carrier ❺, insulation insert ❻, and outer shell ❼ of the plug in line with one another.
  2. As described above pass the cable from a bend relief ❶, collet nut ❷, and collet ❸, and finally from earthing cone ❹.
  3. There is now a need to solder the conducting wires to the contacts on the insulator insert ❻.
  4. The insulator insert ❻ should be covered with a split insert carrier ❺, making sure that both the slots of the split insert carrier ❺ and the slots of the insulator insert ❻ are mounted onto each other.
  5. Make sure the earthing cone ❹ and collet ❸ are properly positioned when the split insert carrier ❺ and insulation insert ❻ have been assembled.
  6. The ready insulator insert ❻ needs to be inserted inside the outer shell ❼ of the plug at this point.
  7. It is crucial that, at this stage, both the slots of the insulator insert ❻ as well as the outer shell ❼ of the plug must be aligned with each other in order to function correctly.
  8. It is now possible to tighten the collet nut ❷ onto the outer shell ❼ of the plug after it has been inserted.
  9. In order to keep the cable from bending at the beginning of the plug, the bend relief ❶ is connected with the collet nut ❷.

Assembly-Instructions-for-D-Series-Straight-Plug

Figure 8 Assembly Instructions for D Series Straight Plug

Leave A Message

Scroll to Top

Get Free Catalogue

Fill out the form below, and we will be in touch shortly.

Send Enquiry

Get a Quick Quote!

x